Spring outboard maintenance

What to do before taking the boat out to launch

By David HarrisDavid Harris

Check oil level

Photo by Eden Robbins

No comments

Let’s do launch: Your careful and complete winterizing last year is about to pay off. Be sure to monitor cooling water outflow, oil levels, and general performance during the first few runs.

Out of the water

1. Service or replace spark plugs

They will be very dirty from the fogging they received last fall. Whether you are servicing a one-, two-, or three-cylinder engine, the plugs are located at the rear of the engine block and are far easier to deal with out of the water, where you’ll avoid wrenching your back while hanging over the stern, risking dropped plugs and tools. Before pulling the capped wires off the plugs, mark the ignition wire with tape labels (e.g., ”upper cable to upper plug”) to ensure you reconnect in the proper order.

The engine will misfire or not fire at all if the leads are not connected properly. Remove the plugs using your spark-plug wrench and give them a spray of WD-40, then wipe with a clean rag. Plugs that have seen more than a couple of seasons’ use should be replaced.

2. Change the fuel filter

Getting rid of the old fuel that has been stagnating in the filter helps ensure a quick start-up. Most filters are located just inside the cowling; follow the fuel line to find yours. Depending on your engine, you’ll find one of three basic types. Older two-stroke engines may have a circular plastic disc held in place with a single centre screw which, when removed, reveals a screen filter that can be gently cleaned using a small amount of gasoline and an old toothbrush. It lasts a long time, but if it is ripped or has any holes, you should replace it. Newer four-stroke engines have a user-friendly canister-style filter with a mesh element. Remove and clean in the same way, but note that these filters are more delicate; replace if damaged or if the gooey buildup won’t brush off. Not shown are in-line filters, found on some brands of two- and four-strokes, which can’t be cleaned and require replacement as much as once a season. When changing any filter, a little gas is bound to spill, so keep a cloth handy. Be sure to use the recommended part for replacement.

3. Check oil level and condition

Whether your engine is a two-stroke or a four-stroke, oil is the key to long engine life and the level should be monitored carefully throughout the season. Four-strokes use a dipstick (similar to your car’s) with high and low marks to verify oil level (above, left). Oil should appear clean (if you were on the ball and changed it last fall) and its level should be at the full mark. For oil-injected two-strokes, check the oil reservoir level and fill if necessary. Depending on the engine type and age, the reservoir will be either within the engine cowling or remotely mounted near the engine and connected by oil-feed hoses. Check your manual to see if priming the oil-injection system is required after prolonged storage.

4. Check lower-unit gear oil

Since you changed the gear oil last season (you did, didn’t you?), a quick visual check will tell you if any fluid has leaked out over the winter. If no dripping or seeping is apparent, you’re good to go. If you suspect a leak, follow the winter lay-up procedure (see winter maintenance, #6) to drain the oil. Check the condition of the nylon washers that seal the vent screws and the fill screws of the lower unit and replace them, if necessary, before refilling the gear case. If leaking continues, suspect worn prop-shaft seals or a cracked casing — and book an appointment with your marine mechanic for replacement.

5. Clear water intake and outflow

Spiders love to climb in these small orifices (just as they like your propane barbecue valves); a pipe cleaner or a small piece of wire can be used to clear out any flow-clogging debris.

6. Lubrication

Use the grease or oil recommended in your manual or by your dealer to lubricate the gear shift and throttle linkages, engine mounting clamps, and cowling release mechanism — in short, anything that moves. Some engines have grease-gun fittings at pivot points for turning and tilting the engine.

This article was originally published on May 15, 2007


Jump to a section

article

No comments

You need to be logged in or a registered user to leave a comment

Log in  |  Register

Tonight on Cottage Life

  • 06:00 pmCOLIN AND JUSTIN'S CABIN PRESSURE
  • 06:30 pmCOLIN AND JUSTIN'S CABIN PRESSURE
  • 07:00 pmCOLIN AND JUSTIN'S CABIN PRESSURE
  • 07:30 pmCOLIN AND JUSTIN'S CABIN PRESSURE
  • 08:00 pmCOLIN AND JUSTIN'S CABIN PRESSURE
  • 08:30 pmCOLIN AND JUSTIN'S CABIN PRESSURE
  • 09:00 pmBUYING HAWAII
  • 09:30 pmBUYING HAWAII
  • 10:00 pmBUYING THE BAYOU
  • 10:30 pmWHAT'S FOR SALE
  • 11:00 pmGEORGE CLARKE'S AMAZING SPACES - SEASON 3
View Full Schedule

MOST POPULAR


David Harris